A dual-droplet approach for measuring the hygroscopicity of aqueous aerosol
- Department of Chemistry, University of California Riverside, Riverside CA 92521, USA
Correspondence: James F. Davies (email@example.com)
Accurate characterization of the water activity and hygroscopicity of aqueous aerosol material allows us to predict the chemical and physical state of aerosol particles exposed to humid conditions in the environment. The hygroscopicity of aerosol determines the size, phase morphology, viscosity, chemical reactivity, and optical properties of constituent particles and directly impacts their ability to form clouds in the atmosphere. In this work, we describe measurements of hygroscopicity using a linear quadrupole electrodynamic balance (LQ-EDB). We levitate two droplets, one droplet that acts as a relative humidity (RH) probe and one sample droplet, and expose them to controlled environmental conditions. We describe the development of an RH measurement using probe droplets of aqueous NaCl or LiCl, allowing for precise in situ measurements of RH in the LQ-EDB chamber. We demonstrate that the RH may be determined with an accuracy of 0.5 % at 50 % RH and better than 0.1 % at 90 % RH using NaCl, and we show that LiCl is effective at characterizing the RH from ∼ 10 % RH up to ∼ 90 %. We simultaneously measure the response of sample droplets containing aqueous material (including ammonium sulfate, citric acid, 1,2,6-hexanetriol, and tetra-ethylene glycol) and report hygroscopic growth via their radial growth factors. We use established thermodynamic models to validate the accuracy of the RH probe and to compare with the measured hygroscopicity of the samples. This approach shows significant advantages over other methods for accurately characterizing the hygroscopicity of samples with a range of characteristics, such as high viscosity and vapor pressure.
The hygroscopicity of aerosol has been of interest to scientists for many years as it plays an important role in the phase morphology, chemical reactivity, optical properties, and cloud-forming efficiency of aerosol particles (Chim et al., 2017; Freedman, 2017; Riemer et al., 2019; Chan et al., 2005; Lam et al., 2021; Denjean et al., 2015; Kulmala et al., 2017). Hygroscopicity describes the ability of a solute to lower the water activity in solution – at the same molar concentration, a hygroscopic compound will reduce the water activity to a greater extent than a non-hygroscopic or less hygroscopic compound. For ideal aqueous solutions, Raoult's law may be used to equate the water activity to the mole fraction of water. However, aqueous aerosols in the atmosphere are rarely ideal solutions, and relating the water activity to the amount of solute is more complicated. For aerosol at equilibrium, the water activity is determined by the water saturation ratio (Senv) of the gas phase:
where pw(T) is the vapor pressure of water at temperature T, and is the saturation vapor pressure. The relative humidity (RH) is equal to this fraction expressed as a percentage. The hygroscopicity may be equivalently described as the amount of condensed-phase water associated with aerosol under a given RH and will determine many physical and chemical characteristics of the aerosol that vary with the amount of water, including viscosity (Reid et al., 2018), refractive index (Cotterell et al., 2017; Day et al., 2000), rates of molecular diffusion (Bones et al., 2012; Marshall et al., 2016; Shiraiwa et al., 2011), reactive uptake coefficients (Davies and Wilson, 2015; Gržinić et al., 2015), and acidity and pH (Pye et al., 2020). Additionally, hygroscopicity plays an important role in regulating cloud formation via the Köhler equation. Aerosol particles capable of forming cloud droplets, known as cloud condensation nuclei (CCN), exhibit a water saturation ratio (Sd) that is a function of the water activity of the aqueous phase and the Kelvin factor. At equilibrium, Senv=Sd, but for cloud formation to occur, Senv must rise above the maximum value of Sd, known as the critical supersaturation, a value that is reduced by hygroscopic solutes. While hygroscopicity and CCN activity are closely related, studies have shown that measurements of hygroscopicity at subsaturated RH can deviate from estimates of hygroscopicity derived from CCN activity measurements, which is attributable to solubility and surface tension effects (Petters and Kreidenweis, 2013, 2008, 2007; Ruehl et al., 2010, 2016). Deriving a complete understanding of the CCN activity and physical properties of aerosol particles across the full range of RH requires a careful approach utilizing both experimental methods and models (Tang et al., 2019).
To characterize aerosol hygroscopicity, it is common to measure the hygroscopic growth of particles as a function of RH in subsaturated conditions, necessitating accurate measurements of particle size and RH. Given that size depends on the amount of non-volatile hygroscopic material, hygroscopic growth measurements are typically reported using growth factors relating the hydrated size at a given RH to the dry amount of solute at 0 % RH. Determining the RH using capacitance probes is common; however, most electrical probes suffer from uncertainties on the order 1 %–2 % and are typically positioned ex situ with respect to the sample (Chen and Chen, 2017). There are several methods that use the response of a probe droplet to determine the in situ RH with very high accuracy and precision. The first example of this was reported by Walker et al. (2010) using optical tweezers capable of confining multiple droplets (Walker et al., 2010). One droplet would contain a well-understood solute, such as sodium chloride, to act as a probe, while the other droplet would contain the sample of interest, such as ammonium sulfate. The equilibrium response of the probe droplet would inform the RH of the system, allowing the response of the sample to be attributed to an RH with lower than 1 % accuracy. While effective, this method proved challenging as confining droplets with independent compositions is not straightforward in optical tweezers, as samples are introduced in a nebulized aerosol plume, and some assumptions of the initial state of the particles is required that can lead to some uncertainty in the measurement. Furthermore, the hygroscopicity of semi-volatile material can be challenging to measure using equilibrium droplet approaches, as the amount of solute changes over the course of the measurement. The more rapid the measurement, the less significant the change in dry mass becomes. For typical hygroscopic growth measurements, the RH is changed slowly to allow the probes and sample to fully equilibrate.
More recently, a hygroscopic growth method was developed using a cylindrical electrodynamic balance whereby the rate of water evaporation was used as a measure of the RH (Davies et al., 2013). Sample droplets and probe droplets were introduced sequentially, and the rate of water evaporation from the probe droplet was used to infer the water activity in the droplet, with its size giving an indication of the solute concentration. This method infers equilibrium hygroscopicity from water evaporation kinetics and has proven to be rapid and accurate in characterizing the hygroscopic growth at high RH, with some limitations (Rovelli et al., 2016). The rate of water evaporation cannot be too fast, as this leads to temperature changes in the droplet that are not accurately captured by mass transport models (Su et al., 2018). Furthermore, water transport kinetics are assumed to be limited only by gas-phase diffusion, and thus water diffusion limitations in the droplet will lead to increased uncertainty. Slow evaporation and rapid water diffusion are typically encountered at high RH, but at low RH diffusion limitations in the particle may limit the rate of water evaporation, leading to the erroneous assumption that the solute lowers the water activity and is more hygroscopic.
In this work, we present an updated equilibrium hygroscopicity measurement using multiple droplets confined within a linear quadrupole electrodynamic balance (LQ-EDB). We describe the new method and show hygroscopic growth data compared to literature data and thermodynamic models. We demonstrate several advantages over previous methods. (1) The sample and probe droplets can be introduced independently, with no risk of cross-contamination. (2) The equilibrium size is measured, allowing the hygroscopicity of samples that exhibit kinetic limitations to be studied. (3) Rapid RH growth curves can be obtained, allowing semi-volatile species to be probed. (4) RH is determined in situ with high accuracy across the whole RH range.
2.1 Particle levitation
A linear quadrupole electrodynamic balance (LQ-EDB) was used to levitate multiple droplets in a linear array under controlled environmental conditions. The general technique and our specific implementation have been described previously (Hart et al., 2015; Jacobs et al., 2017; Price et al., 2020; Davies, 2019). Briefly, droplets are introduced into an aluminum chamber using a piezoelectric droplet dispenser (Microfab MJ-ABP-01) powered with an in-house-developed voltage pulser. As the droplets are produced, a net negative charge is imparted due to the presence of an induction electrode set at +200 to +500 V producing a charge on the order of 20–100 fC (Davies, 2019; Haddrell et al., 2012). The droplets become confined to the linear axis of the rods and fall to an equilibrium height above a balancing DC electrode at voltage VDC. In this work, two separate droplet dispensers and induction electrodes are used to introduce two droplets of different composition in quick succession. This allows both droplets to be stabilized by the electric fields, and their position in the trap is varied with a single VDC, regulated by a proportional–integral–derivative (PID) feedback loop to stabilize the position. Both droplets are illuminated by a laser for visual analysis, and one droplet at a time is illuminated by an LED for spectroscopic analysis, with full manual and automated control through a LabVIEW interface.
2.2 Optical characterization
When illuminated by broadband light from an LED, droplets will act as a spherical cavity, and certain wavelengths will meet the condition for total internal reflection and become resonant in the cavity. Light of these wavelengths is scattered efficiently and will appear as sharp peaks in the backscattered spectrum. We measure the backscattered spectrum using an Ocean Optics HR4000+ spectrometer and observe clear resonant peaks – this is the Mie resonance spectrum (see Fig. S1 in the Supplement). Using Mie theory, the algorithms of Preston and Reid (2013), and an in-house-developed LabVIEW user interface, the positions of the peaks are determined and used to find the radius and the real part of the refractive index (RI) using a first-order Cauchy dispersion expression, with parameters m0 and m1. The diameter is determined with ∼ 10 nm accuracy, while the refractive index uncertainty ranges from ±0.001 to ±0.005 depending on the peaks present in the spectrum. To verify the resulting size and RI, a full spectrum is simulated by Mie theory using the best-fit size and RI and used for visual verification of the fit, as shown in Fig. S1. The spectra are measured over the wavelength range 640–680 nm, and the RI is reported at 589 nm using the first-order Cauchy relation:
2.3 Multiple droplet method
In order to characterize the size and RI of multiple droplets, we programmatically move the droplets up and down by varying VDC to switch the sample illuminated by the LED. In order to ensure that any changes in position are compensated for by the DC feedback loop, the droplets are switched every 10 s. This leads to some blurred spectra during the switch between the two samples; however, these do not impact the analysis of the other frames and can be easily discarded. Spectra are saved in separate files for each sample and analyzed as described above.
2.4 Characterizing the dry size
In order to characterize the hygroscopicity, a measure of the amount of solute is required. Usually, this is referenced to the size of the dry particle either in terms of the dry mass or a spherical equivalent dry volume, and mass or radial growth factors (mGF or rGF) are reported. However, direct measurements of the dry particle size are challenging. In a typical EDB, the balancing voltage V0 under dry conditions is used to indicate the dry mass, although this has some limitations as it assumes a constant charge over time, which is not always achieved (Haddrell et al., 2012). Other methods have used the starting size and solute concentration (Davies et al., 2013; Rovelli et al., 2016) or the measured refractive index (Cotterell et al., 2014). Here, we compare several approaches for determining the dry size. The first (Method 1) relies on measuring the deliquescence of well-characterized solid particles – this approach is used for inorganic particles and is described in Sect. 3.1. We compare this method to the use of the refractive index to characterize solute concentration and subsequently determine dry size (Method 2). For particles without a well-defined deliquescence point, such as most organic particles, we explore two further options – one involves simply measuring the size under 0 % RH (Method 3), while the other correlates the measured size at high RH with the predicted growth factor from a thermodynamic model (see Sect. 2.6), allowing the dry size to be estimated (Method 4). These methods are summarized in Table 1 and are discussed further and applied in Sect. 3.2.
2.5 Environmental conditions
The relative humidity in the chamber is regulated by varying the mixing ratio of humidified and dry N2 gas at a flow rate of 200 sccm. The water bath used to generate the humidity is housed in the reservoir of a recirculating chiller, which is used to control the temperature of the LQ-EDB chamber and avoid temperature changes associated with lab temperature deviations. The temperature of the chamber and water bath is held below ambient (at 18∘) to reduce condensation in the tubing. This setup allows the RH to be varied from dry conditions up to ∼ 95 % RH. For the measurements described here, the RH was either varied stepwise in 5 %–10 % increments or in a pseudo-continuous manner, whereby 0.5 % RH changes were initiated in time intervals down to 5 s, allowing the full RH range to be sampled in under 20 min.
2.6 Thermodynamic models
We make use of two common thermodynamic models in this work – the Extended Aerosol Inorganic Model (E-AIM) (Clegg et al., 1998, 2001) and the Aerosol Organic–Inorganic Mixtures Functional groups Activity Coefficients (AIOMFAC) (Zuend et al., 2011, 2008) model. Both allow the RH-dependent properties of inorganic and organic particles to be predicted based on empirical data and thermodynamic predictions. The E-AIM reports a density along with mass fraction data, allowing radial growth factors to be calculated. The AIOMFAC model only reports a mass fraction, and the density is estimated using a volume-additive approach, as described in the Supplement. The models are used to compare with our measurements and for deriving the RH from measured radial growth factors of probe particles.
3.1 In situ measurements of relative humidity using a droplet
The relative humidity inside the chamber is a function of the amount of gas-phase water and temperature. The RH may be probed using a capacitance probe or a dew-point hygrometer, but these methods have limited accuracy due to their nonlinear response, hysteresis on hydration or dehydration, and their location relative to the sample that may result in temperature changes. The size response of a droplet to changes in RH may be used to indicate the RH for well-characterized particles. In this section, we describe the development and use of an NaCl droplet to probe RH > 50 % and LiCl to probe RH > 10 %. The upper RH is limited by the dynamic range of size measurement accessible to the Mie resonance sizing method.
3.1.1 Sodium chloride droplet-based RH probe
The size and refractive index of two sodium chloride particles were measured as the RH was varied from around 90 % to 50 % RH (Fig. 1a). These data were used to infer the RH in two ways: (1 – the size method) a polynomial fit (with coefficients shown in Table 2) of water activity versus radial growth factor (GF), obtained from E-AIM (Clegg et al., 1998, 2001), was used to relate measured GF to RH; and (2 – the RI method) the measured RI was used to calculate the RH based on the parameterization of Cotterell et al. (Cotterell et al., 2017). In order to determine the radial GF, the dry size of each particle was determined from the size of the droplet at its deliquescence RH (dRH = 75.5 %), identified by slowly increasing the RH exposed to a dry particle of NaCl (see the Supplement and Fig. S2). A radial GF of 1.9 was used to calculate the dry size, determined from E-AIM, and the GF for all other sizes was determined. The RH values determined by the size and RI methods are shown in Fig. 1b and c, respectively, for both droplets.
The size of the droplet is obtained with a high precision, within 10 nm, while the RI is less well-constrained, varying by ±0.001 to ±0.005. When determining the RH, the larger uncertainty in the RI leads to a larger uncertainty in RH, with an estimated error of ±1.0 %. The size method, on the other hand, results in an RH uncertainty of ±0.25 % at 50 % RH and a diminishingly small uncertainty at high RH, with ±0.05 % at > 90 % RH. The uncertainty in the size becomes less significant at high RH, while the uncertainty in the RI becomes more significant due to how the RI varies with RH (Fig. S3).
The absolute accuracy of these methods depends on the accuracy of the source data. E-AIM has been developed with many experiments used to correct theoretical prediction with empirical relationships. Given the abundance of data describing the hygroscopicity of NaCl, these predictions are considered highly accurate (Peng et al., 2016; Zieger et al., 2017; Laskina et al., 2015). In the work of Cotterell et al. (2017) the RI is measured using optical tweezers as a function of RH. The resulting parameterization will implicitly encompass the uncertainty of the RH probes used in that work, thus negating the advantages of using a droplet as an RH probe. There is a relatively broad spread of refractive index values attributed to supersaturated NaCl solutions, and at 50 % RH the RI values in the literature span ∼ 1.41–1.42, while at high RH the agreement is much closer (Bain and Preston, 2020). Due to the higher precision and accuracy of the size method compared to the RI method for determining the RH, we will adopt the size method going forwards to determine RH using a droplet probe.
To test the accuracy of the droplet probe method, a direct comparison to another well-characterized chemical system was performed. Ammonium sulfate (AS) is the next most abundant salt in the atmosphere after NaCl and one of the most widely studied atmospherically relevant inorganic species. Using an NaCl droplet as a probe of the RH, the radius of an AS droplet was measured over the RH range from ∼ 45 % to 95 %. The size of the AS droplet at the deliquescence RH (dRH = 80 %) and corresponding growth factor of 1.48 were used to determine the dry size of the particle to calculate the radial growth factors. Both discrete RH steps and continuous linear RH changes were applied to samples. Figure 2a shows the hygroscopic growth curve of AS determined in this way compared to the E-AIM prediction, with Fig. 2b showing the difference in the rGF values. We observe agreement within 0.5 % (at worst) until just below 50 % RH, at which the data deviate from the prediction. This is attributed to a breakdown of the RH measurement using NaCl as a probe below this point, as evidenced by the apparent RH showing ∼ 40 % at the point of efflorescence for NaCl at a growth factor of ∼ 1.52. This is lower than the typical eRH of NaCl (∼ 45 %, although not a thermodynamically well-defined point) (Gao et al., 2007). The accuracy of the NaCl probe is therefore judged to be sufficient only above 50 % RH.
3.1.2 Lithium chloride droplet-based RH probe
The efflorescence of NaCl at ∼ 45 % RH and inaccuracy at < 50 % RH limit its application to measure RH under dry conditions. Instead, LiCl, which deliquesces at 11.3 % RH and effloresces only under exposure to < 10 % RH, may be used. Unlike NaCl, LiCl is not well-characterized or represented by thermodynamic models. Water activity data have been reported by Robinson (1945), and the AIOMFAC model predicts a similar dependence (Zuend et al., 2011). However, translating the reported mass fraction dependence to a growth factor dependence requires knowledge of the solution density. Figure 3 shows the radial GF of LiCl derived from the mass fraction data reported by AIOMFAC. A volume-additive density approach was adopted, as described in the Supplement. The radial GF at the deliquescence point is taken to be 1.525, and measurements of LiCl using an NaCl droplet probe were performed, showing a clear deviation from the AIOMFAC predication below ∼ 70 % RH, but with agreement at higher RH within ∼ 0.5 %. A lack of available data with an NaCl probe below 50 % RH was remedied using an ammonium sulfate droplet, extending the LiCl data down to ∼ 35 %. A polynomial fit of the RH was determined from the experimental data and connected to the point of deliquescence. The accuracy of the RH is expected to be limited over the range in which data are not available (12 % to 35 % RH), but the precision and reproducibility are on the order of ±0.1 % based on the uncertainty in the size measurements. The coefficients of the polynomial fit are shown in Table 2.
3.1.3 Advantages and limitations of the dual-droplet method
A key advantage of this approach comes from how it can account for the effects of temperature, which are known to cause problems with external RH probes but can be fully accounted for with an in situ probe of RH. The solubility of NaCl varies only weakly with temperature, and changes in hygroscopicity and deliquescence RH may be accounted for using different E-AIMs that account for temperature (Friese and Ebel, 2010). The accuracy and precision of this approach is also a significant advantage, with a time response for non-viscous particles limited only by the condensation or evaporation rate of water, which for droplets on the order of 10 µm in size is on the order of a few seconds (Miles et al., 2010).
Despite these advantages, there are some limitations, particularly in the dynamic range of RH that can be probed in a single measurement. Due to the need to measure the size of the particle at dRH in order to determine accurate growth factors, the range of RH that may be probed using LiCl is limited. A particle of 3500 nm at dRH will be ∼ 8000 nm at 95 % RH, and at higher RH it will grow to radii that yield increased uncertainty in the size results, translating to increased uncertainty in the RH. For a similar droplet of NaCl, the highest RH that may be reliably determined is ∼ 99 %. Fewer hygroscopic probes may be developed to explore systems closer to saturation, but this range is currently inaccessible to our methods and will not be explored presently.
3.2 Hygroscopic growth of organic particles
For particles that do not show a deliquescence transition from a dry particle to a wet droplet, determining the dry size using Method 1 is challenging. As introduced earlier, there are several options available, depending on the sample, that offer varying advantages and disadvantages. In Method 2, the measured refractive index can be compared to a calibration of bulk solution RI as a function of concentration or literature data to determine the composition and infer the radial growth factor and/or mass fraction. This approach is widely applicable and is not impacted by changes in dry size due to evaporation. However, the uncertainty associated with the RI is much larger than the radius, leading to reduced accuracy of the hygroscopic growth measurements. Method 3 is applicable to particles that are anhydrous and remain spherical under dry conditions, and the measured size can be used to determine the dry size. This approach is effective for non-volatile components but is limited when samples are semi-volatile and the dry size changes over time. Method 4 takes the measured size at high RH, at which the solution is dilute, and uses a thermodynamic model prediction to determine the solute concentration. Thus, the radial growth factor can be constrained to match the thermodynamic modeling predication at high RH in order to determine a dry size. This approach is limited by the accuracy of the model and, for AIOMFAC, for example, the accuracy of the density approach used to convert from mass fraction to radial growth factor. The three approaches described here are applied to citric acid, 1,2,6-hexanetriol, and tetra-ethylene glycol in the subsequent sections.
3.2.1 Hygroscopicity of citric acid
Citric acid is a highly oxygenated organic molecule that has been used in several studies as a proxy for oxidized organic material in the atmosphere (Davies and Wilson, 2015; Gržinić et al., 2015; Chim et al., 2018). It is highly soluble and will form a viscous aqueous solution at low RH (Davies and Wilson, 2016; Lienhard et al., 2014). The high viscosity limits the rate of transport of water and can yield measurements of states that have not reached equilibrium if insufficient time has passed in a measurement. Due to the formation of a viscous state at low RH, citric acid particles do not efflorescence and may not reach a fully anhydrous state even under dry conditions (Peng et al., 2001).
We measured the size of citric acid droplets across the full RH range alongside an LiCl droplet to probe the RH. At low RH, measurements were performed for extended time periods (up to hours) to ensure the sample droplet achieved an equilibrium composition. The AIOMFAC-derived growth factor was determined using a volume-additive density approach (see the Supplement). Briefly, at the highest measured RH of 85 %, we estimate from AIOMFAC a mass fraction of solute (MFS) of 0.569, which yields 1.29 g cm−3 using the density of the crystal (1.66 g cm−3), giving a dry size for this dataset of 4789 nm and allowing rGF to be determined (Fig. 4a). If instead we assume that the density of the citric acid in solution reflects the subcooled density, as predicted using the online tool UManSysProp (ρ=1.47 g cm−3) (Barley et al., 2013), we estimate the density at 85 % RH to be 1.22 g cm−3, giving a dry size of 4693 nm (Fig. 4b). These different dry sizes account for the differences in the experiment results between Fig. 4a and b. Using the volume-additive density approach with crystal density shown in Fig. 4a, the AIOMFAC-derived growth curve deviates significantly from our data below ∼ 70 % RH. When the subcooled melt density is used for the density of CA in solution, the AIOMFAC prediction and data agree closely, with the largest deviation of 0.4 % of the radial growth factor (Fig. 4b). Both predictions reference a dry particle with a density equal to the crystal density. It is clear these data do not tend towards unity under dry conditions, and this is due to the formation of a stable hydrate and the amorphous state of the particle – the citric acid will not form a crystal even at 0 % RH, and thus the size will always be larger than the dried crystalline particle. We further compare our growth curves to the prediction of Lienhard et al. (2012) by converting their reported solution density to a rGF referencing a crystalline dry particle. This prediction is shown in Fig. 4a and b, with some deviations from our measurements at high and low RH, respectively, for the two density methods. There is no single value of the dry size that would allow our experimental results to yield agreement with the data of Lienhard et al. (2012).
An alternative method for determining the radial growth factor is via the measured refractive index (RI). Using the data of Lienhard et al. (2012), we determine the MFS values associated with the measured RI and compare these directly to AIOMFAC in Fig. 4c. By estimating the density as described above, we can also determine the rGF from these MFS values, and these estimates are shown in Fig. 4a and b using the crystal and subcooled density, respectively. Both estimates yield radial growth that is significantly lower than the AIOMFAC predictions and radius-derived rGF measurements as well as mass fractions that are higher. Indeed, at the lowest RH, a mass fraction > 1 is predicted, which is likely erroneous. To explore the origin of this error, we closely compared the Mie resonance spectra with the predicted spectra based on the best-fit size and RI, and we observe excellent agreement for both high- and low-RH spectra (Fig. 5a and b, respectively). Equivalently good fits are noted across the whole RH range, indicating that the RI coefficients (m0 and m1) derived from the sizing process are accurate. However, it is important to note that we report the RI at 589 nm to be consistent with literature data and use the Cauchy relation along with m0 and m1 to extrapolate to this wavelength. Our measurements only span the range 640–680 nm, and thus we can only be sure of the accuracy of these coefficients in this wavelength range. The uncertainty range that we quote, ±0.005, reflects this extrapolation, and indeed the RI that we measure appears to be larger than the Lienhard data by ∼ 0.005 (Lienhard et al., 2012). We tested the use of an additional term in the Cauchy expression, , but observed no significant differences to the RI at 589 nm.
While we acknowledge there is likely some significant uncertainty in the RI at 589 nm from our measurements, there is overlap with the literature data when both uncertainty ranges are considered. Lienhard et al. (2012) report an uncertainty of 0.0025 for the RI, which is slightly smaller uncertainty than reported here, possibly due to the use of first-order resonance modes in the Raman spectrum that yield an improved fit. While the exact source of the discrepancy cannot be definitively determined, these observations indicate that the RI is not currently a reliable method of characterizing the hygroscopic growth due to limited precision and accuracy.
3.2.2 Hygroscopicity of 1,2,6-hexanetriol
The systems explored so far have contained non-volatile or very low-volatility solutes. When the vapor pressure is sufficiently high, evaporation of solute from the droplet will occur, leading to a dry size that decreases over time. As we have already determined that using the refractive index to indicate the hygroscopic growth is not accurate, we must rely on measurements of the size and correct for any changes due to evaporation. 1,2,6-Hexanetriol is an oxygenated organic molecule that has a vapor pressure of 0.2 mPa (Cotterell et al., 2014). Over the course of 1 h under dry conditions, a 5000 nm particle will change in size by approximately 50 nm, which leads to a measurable change in the growth curve when using the measured dry size, as shown in the inset in Fig. 6. Evaporation slows as the RH increases and the activity of the evaporating component decreases. By rapidly varying the RH over a humidity cycle and updating the dry size each time dry conditions are encountered, the change in dry size due to evaporation can be corrected, and the growth curve obtained yields excellent agreement with the AIOMFAC prediction within 1 % across the whole measure range. While this system is slowly evaporating, it is likely representative of semi-volatile organic molecules in the atmosphere (Bilde and Pandis, 2001), which will only persist in aerosol if their vapor pressures are sufficiently low.
3.2.3 Hygroscopicity of tetra-ethylene glycol
In the case of particles containing solutes with higher vapor pressures than 1,2,6-hexanetriol, measurements must be performed rapidly in order to reduce the amount of evaporation that occurs as the RH scans across the measured range. Tetra-ethylene glycol (4-EG) has a vapor pressure of ∼ 16.9 mPa (Krieger et al., 2018) and for a 5000 nm particle will lose around 60 nm of size over 100 s under dry conditions. The evaporation rate is suppressed at higher RH due to a reduction in the activity, and thus significant evaporation occurs only as dry conditions are approached. The size of a droplet exposed to a dehumidifying–humidifying cycle is shown in Fig. 7a, and the corresponding hygroscopic growth of 4-EG is shown in Fig. 7b. When using the size at the lowest RH to indicate the dry radius, we will overpredict the radial growth factor for the dehumidifying cycle and underpredict the growth factor for the humidifying cycle – in both cases the dry size will be smaller at the end of the measurement. Even with an RH change over 300 s, this leads to clear upper and lower bounding on the hygroscopic growth curve shown in Fig. 7b. Changing the RH faster is possible, and using a probe droplet to measure the RH avoids the need for fast-changing external capacitance probes. However, this will result in a rapid change in size, which will blur the resonance peaks used to determine the size. The speed of the change in RH is thus limited by the minimum exposure time that yields well-resolved peaks of sufficient intensity to characterize. In these experiments, an exposure time down to 0.2 s was used to achieve the 300 s cycle, and this represents the lowest workable timescale with the current experimental configuration. More rapid measurements would be possible with a different spectrometer and illumination source, and these would be necessary to accurately probe the hygroscopicity of material with volatility greater than the compounds reported here.
Hygroscopic growth measurements are not new, but they continue to play an important supporting role when predicting rates of diffusion, viscosity, phase morphology, optical properties, and reactivity. The dual-droplet method reported here allows for very accurate measurements of RH and hygroscopicity for a variety of samples over a broad range of conditions. The influence of temperature on hygroscopic growth may be explored without impacting the accuracy of the RH measurements, as the temperature response of the hygroscopic growth and deliquescence RH can be well-characterized and the particle is positioned in situ with the sample, yielding the best possible accuracy. The high precision in measurements will allow subtle changes in hygroscopicity to be determined, exploring, for example, observations of small changes in diffusion and/or viscosity due to changes in particle composition (Wallace et al., 2021). The accuracy of measurements at high RH will provide an effective bridge between hygroscopic growth measurements under subsaturated conditions and cloud formation measurements under supersaturated conditions, which can show significant deviations due to solubility and surface tension effects (Petters and Kreidenweis, 2013, 2007, 2008). In addition to characterizing hygroscopicity, dual-droplet measurements may also be applied to identify the RH and temperature of phase transitions and liquid–liquid phase separation (Stewart et al., 2015; Gorkowski et al., 2020), RH-dependent water diffusion coefficients (Preston et al., 2017), vapor pressures (Cai et al., 2014), and optical properties (Cotterell et al., 2017; Bain and Preston, 2020; David et al., 2016) in measurements analogous to those previously performed with single droplets.
The use of NaCl and LiCl solution droplets as in situ probes of relative humidity has been demonstrated. In both cases, the size of the droplet at the deliquescence point is used to characterize the dry size from the known radial growth factors at these points. This allows the radial growth factor to be determined at any arbitrary RH from measured size. Using either E-AIM (for NaCl) or a parameterization derived from measurements, we translate the radial GF to RH and show a precision of ∼ 0.5 % at 50 % and better than 0.1 % above 90 % RH for NaCl. The LiCl probe was shown to be effective across a wider range of RH owing to its very low deliquescence RH. We used both droplet probes to characterize the RH for a range of measurements to validate the accuracy and applicability of the technique, with excellent agreement shown with established thermodynamic models for ammonium sulfate, citric acid, and 1,2,6-hexanetriol. We also report the hygroscopic growth of tetra-ethylene glycol using a rapid RH cycle (over 300 s) to minimize the influence of evaporation on the measured size. These measurements demonstrate the utility and accuracy of the dual-droplet method for accurate hygroscopic growth characterization. Future work will incorporate this approach for characterizing other RH-dependent properties, such as water diffusion rates, viscosity, vapor pressures, and optical properties.
All data not directly reported in the paper will be made available on request.
The supplement related to this article is available online at: https://doi.org/10.5194/amt-14-5001-2021-supplement.
JFD designed the research. JMC, RKK, CSS, and CLP performed the measurements. JFD and JMC analyzed the data. JFD and JMC wrote the paper.
The authors declare that they have no conflict of interest.
Publisher's note: Copernicus Publications remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
We would like to acknowledge the startup funding provided by the University of California Riverside.
This research has been supported by the University of California Riverside.
This paper was edited by Mingjin Tang and reviewed by two anonymous referees.
Bain, A. and Preston, T. C.: The wavelength-dependent optical properties of weakly absorbing aqueous aerosol particles, Chem. Commun., 56, 8928–8931, https://doi.org/10.1039/D0CC02737E, 2020.
Barley, M. H., Topping, D. O., and McFiggans, G.: Critical Assessment of Liquid Density Estimation Methods for Multifunctional Organic Compounds and Their Use in Atmospheric Science, J. Phys. Chem. A, 117, 3428–3441, https://doi.org/10.1021/jp304547r, 2013.
Bilde, M. and Pandis, S. N.: Evaporation Rates and Vapor Pressures of Individual Aerosol Species Formed in the Atmospheric Oxidation of α- and β-Pinene, Environ. Sci. Technol., 35, 3344–3349, https://doi.org/10.1021/es001946b, 2001.
Bones, D. L., Reid, J. P., Lienhard, D. M., and Krieger, U. K.: Comparing the mechanism of water condensation and evaporation in glassy aerosol, Proc. Natl. Acad. Sci. USA, 109, 11613–11618, https://doi.org/10.1073/pnas.1200691109, 2012.
Cai, C., Stewart, D. J., Reid, J. P., Zhang, Y., Ohm, P., Dutcher, C. S., and Clegg, S. L.: Organic Component Vapor Pressures and Hygroscopicities of Aqueous Aerosol Measured by Optical Tweezers, J. Phys. Chem. A, 119, 704–718, https://doi.org/10.1021/jp510525r, 2014.
Chan, M. N., Choi, M. Y., Ng, N. L., and Chan, C. K.: Hygroscopicity of Water-Soluble Organic Compounds in Atmospheric Aerosols: Amino Acids and Biomass Burning Derived Organic Species, Environ. Sci. Technol., 39, 1555–1562, https://doi.org/10.1021/es049584l, 2005.
Chen, J. and Chen, C.: Uncertainty Analysis in Humidity Measurements by the Psychrometer Method, Sensors, 17, 368, https://doi.org/10.3390/s17020368, 2017.
Chim, M. M., Chow, C. Y., Davies, J. F., and Chan, M.: Effects of Relative Humidity and Particle Phase Water on the Heterogeneous OH Oxidation of 2-Methylglutaric Acid Aqueous Droplets, J. Phys. Chem. A, 121, 1666–1674, https://doi.org/10.1021/acs.jpca.6b11606, 2017.
Chim, M. M., Lim, C. Y., Kroll, J. H., and Chan, M.: Evolution in the reactivity of citric acid towards heterogeneous oxidation by gas-phase OH radicals, ACS Earth Space Chem., 2, 1323–1329, https://doi.org/10.1021/acsearthspacechem.8b00118, 2018.
Clegg, S. L., Brimblecombe, P., and Wexler, A. S.: A thermodynamic model of the system H – NH4 – Na – SO4 – NO3 – Cl – H2O at at 298.15 K, J. Phys. Chem. A, 102, 2155–2171, 1998.
Clegg, S. L., Seinfeld, J. H., and Brimblecombe, P.: Thermodynamic modelling of aqueous aerosols containing electrolytes and dissolved organic compounds, J. Aerosol Sci., 32, 713–738, 2001.
Cotterell, M. I., Mason, B. J., Carruthers, A. E., Walker, J. S., Orr-Ewing, A. J., and Reid, J. P.: Measurements of the evaporation and hygroscopic response of single fine-mode aerosol particles using a Bessel beam optical trap., Phys. Chem. Chem. Phys., 16, 2118–2128, https://doi.org/10.1039/c3cp54368d, 2014.
Cotterell, M. I., Willoughby, R. E., Bzdek, B. R., Orr-Ewing, A. J., and Reid, J. P.: A complete parameterisation of the relative humidity and wavelength dependence of the refractive index of hygroscopic inorganic aerosol particles, Atmos. Chem. Phys., 17, 9837–9851, https://doi.org/10.5194/acp-17-9837-2017, 2017.
David, G., Esat, K., Ritsch, I., and Signorell, R.: Ultraviolet broadband light scattering for optically-trapped submicron-sized aerosol particles, Phys. Chem. Chem. Phys., 18, 5477–5485, https://doi.org/10.1039/C5CP06940H, 2016.
Davies, J. F.: Mass, charge, and radius of droplets in a linear quadrupole electrodynamic balance, Aerosol Sci. Tech., 53, 309–320, https://doi.org/10.1080/02786826.2018.1559921, 2019.
Davies, J. F. and Wilson, K. R.: Nanoscale interfacial gradients formed by the reactive uptake of OH radicals onto viscous aerosol surfaces, Chem. Sci., 6, 7020–7027, https://doi.org/10.1039/c5sc02326b, 2015.
Davies, J. F. and Wilson, K. R.: Raman Spectroscopy of Isotopic Water Diffusion in Ultra-Viscous, Glassy and Gel States in Aerosol Using Optical Tweezers, Anal. Chem., 88, 2361–2366, https://doi.org/10.1021/acs.analchem.5b04315, 2016.
Davies, J. F., Haddrell, A. E., Rickards, A. M. J., and Reid, J. P.: Simultaneous Analysis of the Equilibrium Hygroscopicity and Water Transport Kinetics of Liquid Aerosol, Anal. Chem., 85, 5819–5826, https://doi.org/10.1021/ac4005502, 2013.
Day, D. E., Malm, W. C., and Kreidenweis, S. M.: Aerosol Light Scattering Measurements as a Function of Relative Humidity, J. Air Waste Manage. Assoc., 50, 710–716, https://doi.org/10.1080/10473289.2000.10464103, 2000.
Denjean, C., Formenti, P., Picquet-Varrault, B., Pangui, E., Zapf, P., Katrib, Y., Giorio, C., Tapparo, A., Monod, A., Temime-Roussel, B., Decorse, P., Mangeney, C., and Doussin, J. F.: Relating hygroscopicity and optical properties to chemical composition and structure of secondary organic aerosol particles generated from the ozonolysis of α-pinene, Atmos. Chem. Phys., 15, 3339–3358, https://doi.org/10.5194/acp-15-3339-2015, 2015.
Freedman, M. A.: Phase separation in organic aerosol, Chem. Soc. Rev., 46, 7694–7705, https://doi.org/10.1039/c6cs00783j, 2017.
Friese, E. and Ebel, A.: Temperature Dependent Thermodynamic Model of the System H+-NH-Na+-SO-NO-Cl−-H2O, J. Phys. Chem. A, 114, 11595–11631, https://doi.org/10.1021/jp101041j, 2010.
Gao, Y., Chen, S. B., and Yu, L. E.: Efflorescence relative humidity of airborne sodium chloride particles: A theoretical investigation, Atmos. Environ., 41, 2019–2023, https://doi.org/10.1016/j.atmosenv.2006.12.014, 2007.
Gorkowski, K., Donahue, N. M., and Sullivan, R. C.: Aerosol Optical Tweezers Constrain the Morphology Evolution of Liquid-Liquid Phase-Separated Atmospheric Particles, Chem, 6, 204–220, https://doi.org/10.1016/j.chempr.2019.10.018, 2020.
Gržinić, G., Bartels-Rausch, T., Berkemeier, T., Türler, A., and Ammann, M.: Viscosity controls humidity dependence of N2O5 uptake to citric acid aerosol, Atmos. Chem. Phys., 15, 13615–13625, https://doi.org/10.5194/acp-15-13615-2015, 2015.
Haddrell, A. E., Davies, J. F., Yabushita, A., and Reid, J. P.: Accounting for changes in particle charge, dry mass and composition occurring during studies of single levitated particles, J. Phys. Chem. A, 116, 9941–9953, https://doi.org/10.1021/jp304920x, 2012.
Hart, M. B., Sivaprakasam, V., Eversole, J. D., Johnson, L. J., and Czege, J.: Optical measurements from single levitated particles using a linear electrodynamic quadrupole trap, Appl. Optics, 54, F174, https://doi.org/10.1364/ao.54.00f174, 2015.
Herskowitz, M. and Gottlieb, M.: Vapor-liquid equilibrium in aqueous solutions of various glycols and poly(ethylene glycols). 3. Poly(ethylene glycols), J. Chem. Eng. Data, 30, 233–234, https://doi.org/10.1021/je00040a033, 1985.
Jacobs, M. I., Davies, J. F., Lee, L., Davis, R. D., Houle, F., and Wilson, K. R.: Exploring Chemistry in Microcompartments Using Guided Droplet Collisions in a Branched Quadrupole Trap Coupled to a Single Droplet, Paper Spray Mass Spectrometer, Anal. Chem., 89, 12511–12519, https://doi.org/10.1021/acs.analchem.7b03704, 2017.
Krieger, U. K., Siegrist, F., Marcolli, C., Emanuelsson, E. U., Gøbel, F. M., Bilde, M., Marsh, A., Reid, J. P., Huisman, A. J., Riipinen, I., Hyttinen, N., Myllys, N., Kurtén, T., Bannan, T., Percival, C. J., and Topping, D.: A reference data set for validating vapor pressure measurement techniques: homologous series of polyethylene glycols, Atmos. Meas. Tech., 11, 49–63, https://doi.org/10.5194/amt-11-49-2018, 2018.
Kulmala, M., Korhonen, P., Vesala, T., Hansson, H.-C., Noone, K., and Svenningsson, B.: The effect of hygroscopicity on cloud droplet formation, Tellus B, 48, 347–360, https://doi.org/10.3402/tellusb.v48i3.15903, 2017.
Lam, H. K., Xu, R., Choczynski, J., Davies, J. F., Ham, D., Song, M., Zuend, A., Li, W., Tse, Y.-L. S., and Chan, M. N.: Effects of liquid–liquid phase separation and relative humidity on the heterogeneous OH oxidation of inorganic–organic aerosols: insights from methylglutaric acid and ammonium sulfate particles, Atmos. Chem. Phys., 21, 2053–2066, https://doi.org/10.5194/acp-21-2053-2021, 2021.
Laskina, O., Morris, H. S., Grandquist, J. R., Qin, Z., Stone, E. A., Tivanski, A. V., and Grassian, V. H.: Size Matters in the Water Uptake and Hygroscopic Growth of Atmospherically Relevant Multicomponent Aerosol Particles, J. Phys. Chem. A, 119, 4489–4497, https://doi.org/10.1021/jp510268p, 2015.
Lienhard, D. M., Bones, D. L., Zuend, A., Krieger, U. K., Reid, J. P., and Peter, T.: Measurements of thermodynamic and optical properties of selected aqueous organic and organic-inorganic mixtures of atmospheric relevance, J. Phys. Chem. A, 116, 9954–9968, https://doi.org/10.1021/jp3055872, 2012.
Lienhard, D. M., Huisman, A. J., Bones, D. L., Te, Y.-F., Luo, B. P., Krieger, U. K., and Reid, J. P.: Retrieving the translational diffusion coefficient of water from experiments on single levitated aerosol droplets, Phys. Chem. Chem. Phys., 16, 16677–16683, https://doi.org/10.1039/c4cp01939c, 2014.
Marshall, F. H., Miles, R. E. H., Song, Y.-C., Ohm, P. B., Power, R. M., Reid, J. P., and Dutcher, C. S.: Diffusion and Reactivity in Ultraviscous Aerosol and the Correlation with Particle Viscosity, Chem. Sci., 7, 1298–1308, https://doi.org/10.1039/c5sc03223g, 2016.
Miles, R. E. H., Knox, K. J., Reid, J. P., Laurain, A. M. C., and Mitchem, L.: Measurements of Mass and Heat Transfer at a Liquid Water Surface during Condensation or Evaporation of a Subnanometer Thickness Layer of Water, Phys. Rev. Lett., 105, 116101, https://doi.org/10.1103/PhysRevLett.105.116101, 2010.
Peng, C., Chow, A. H. L., and Chan, C. K.: Hygroscopic Study of Glucose, Citric Acid, and Sorbitol Using an Electrodynamic Balance: Comparison with UNIFAC Predictions, Aerosol Sci. Tech., 35, 753–758, https://doi.org/10.1080/02786820152546798, 2001.
Peng, C., Jing, B., Guo, Y.-C., Zhang, Y.-H., and Ge, M.-F.: Hygroscopic Behavior of Multicomponent Aerosols Involving NaCl and Dicarboxylic Acids, J. Phys. Chem. A, 120, 1029–1038, https://doi.org/10.1021/acs.jpca.5b09373, 2016.
Petters, M. D. and Kreidenweis, S. M.: A single parameter representation of hygroscopic growth and cloud condensation nucleus activity, Atmos. Chem. Phys., 7, 1961–1971, https://doi.org/10.5194/acp-7-1961-2007, 2007.
Petters, M. D. and Kreidenweis, S. M.: A single parameter representation of hygroscopic growth and cloud condensation nucleus activity – Part 2: Including solubility, Atmos. Chem. Phys., 8, 6273–6279, https://doi.org/10.5194/acp-8-6273-2008, 2008.
Petters, M. D. and Kreidenweis, S. M.: A single parameter representation of hygroscopic growth and cloud condensation nucleus activity – Part 3: Including surfactant partitioning, Atmos. Chem. Phys., 13, 1081–1091, https://doi.org/10.5194/acp-13-1081-2013, 2013.
Preston, T. C. and Reid, J. P.: Accurate and efficient determination of the radius, refractive index, and dispersion of weakly absorbing spherical particle using whispering gallery modes, J. Opt. Soc. Am. B, 30, 2113–2122, https://doi.org/10.1364/josab.30.002113, 2013.
Preston, T. C., Davies, J. F., and Wilson, K. R.: The frequency-dependent response of single aerosol particles to vapour phase oscillations and its application in measuring diffusion coefficients, Phys. Chem. Chem. Phys., 19, 3922–3931, https://doi.org/10.1039/c6cp07711k, 2017.
Price, C. L., Bain, A., Wallace, B. J., Preston, T. C., and Davies, J. F.: Simultaneous Retrieval of the Size and Refractive Index of Suspended Droplets in a Linear Quadrupole Electrodynamic Balance, J. Phys. Chem. A, 124, 1811–1820, https://doi.org/10.1021/acs.jpca.9b10748, 2020.
Pye, H. O. T., Nenes, A., Alexander, B., Ault, A. P., Barth, M. C., Clegg, S. L., Collett Jr., J. L., Fahey, K. M., Hennigan, C. J., Herrmann, H., Kanakidou, M., Kelly, J. T., Ku, I.-T., McNeill, V. F., Riemer, N., Schaefer, T., Shi, G., Tilgner, A., Walker, J. T., Wang, T., Weber, R., Xing, J., Zaveri, R. A., and Zuend, A.: The acidity of atmospheric particles and clouds, Atmos. Chem. Phys., 20, 4809–4888, https://doi.org/10.5194/acp-20-4809-2020, 2020.
Rard, J. A.: The Isopiestic Method: 100 Years Later and Still in Use, J. Solution Chem., 48, 271–282, https://doi.org/10.1007/s10953-019-00848-4, 2019.
Reid, J. P., Bertram, A. K., Topping, D. O., Laskin, A., Martin, S. T., Petters, M. D., Pope, F. D., and Rovelli, G.: The viscosity of atmospherically relevant organic particles, Nat. Commun., 9, 956, https://doi.org/10.1038/s41467-018-03027-z, 2018.
Riemer, N., Ault, A. P., West, M., Craig, R. L., and Curtis, J. H.: Aerosol Mixing State: Measurements, Modeling, and Impacts, Rev. Geophys., 57, 187–249, https://doi.org/10.1029/2018rg000615, 2019.
Robinson, R. A.: The water activities of lithium chloride solutions up to high concentrations at 25∘, Trans. Faraday Soc., 41, 756–758, https://doi.org/10.1039/TF9454100756, 1945.
Rovelli, G., Miles, R. E. H., Reid, J. P., and Clegg, S. L.: Accurate Measurements of Aerosol Hygroscopic Growth over a Wide Range in Relative Humidity, J. Phys. Chem. A, 120, 4376–4388, https://doi.org/10.1021/acs.jpca.6b04194, 2016.
Ruehl, C. R., Chuang, P. Y., and Nenes, A.: Aerosol hygroscopicity at high (99 to 100 %) relative humidities, Atmos. Chem. Phys., 10, 1329–1344, https://doi.org/10.5194/acp-10-1329-2010, 2010.
Ruehl, C. R., Davies, J. F., and Wilson, K. R.: An interfacial mechanism for cloud droplet formation on organic aerosols, Science, 351, 1447–1450, https://doi.org/10.1126/science.aad4889, 2016.
Shiraiwa, M., Ammann, M., Koop, T., and Pöschl, U.: Gas uptake and chemical aging of semisolid organic aerosol particles, P. Natl. Acad. Sci. USA, 108, 11003–11008, https://doi.org/10.1073/pnas.1103045108, 2011.
Stewart, D. J., Cai, C., Nayler, J., Preston, T. C., Reid, J. P., Krieger, U. K., Marcolli, C., and Zhang, Y. H.: Liquid–Liquid Phase Separation in Mixed Organic/Inorganic Single Aqueous Aerosol Droplets, J. Phys. Chem. A, 119, 4177–4190, https://doi.org/10.1021/acs.jpca.5b01658, 2015.
Su, Y., Miles, R. E. H., Li, Z., Reid, J. P., and Xu, J.: The evaporation kinetics of pure water droplets at varying drying rates and the use of evaporation rates to infer the gas phase relative humidity, Phys. Chem. Chem. Phys., 20, 23453–23466, https://doi.org/10.1039/C8CP05250F, 2018.
Tang, M., Chan, C. K., Li, Y. J., Su, H., Ma, Q., Wu, Z., Zhang, G., Wang, Z., Ge, M., Hu, M., He, H., and Wang, X.: A review of experimental techniques for aerosol hygroscopicity studies, Atmos. Chem. Phys., 19, 12631–12686, https://doi.org/10.5194/acp-19-12631-2019, 2019.
Walker, J. S., Wills, J. B., Reid, J. P., Wang, L., Topping, D. O., Butler, J. R., and Zhang, Y.-H.: Direct Comparison of the Hygroscopic Properties of Ammonium Sulfate and Sodium Chloride Aerosol at Relative Humidities Approaching Saturation, J. Phys. Chem. A, 114, 12682–12691, https://doi.org/10.1021/jp107802y, 2010.
Wallace, B. J., Price, C. L., Davies, J. F., and Preston, T. C.: Multicomponent diffusion in atmospheric aerosol particles, Environ. Sci. Atmos., 1, 45–55, https://doi.org/10.1039/D0EA00008F, 2021.
Zieger, P., Väisänen, O., Corbin, J. C., Partridge, D. G., Bastelberger, S., Mousavi-Fard, M., Rosati, B., Gysel, M., Krieger, U. K., Leck, C., Nenes, A., Riipinen, I., Virtanen, A., and Salter, M. E.: Revising the hygroscopicity of inorganic sea salt particles, Nat. Commun., 8, 15883, https://doi.org/10.1038/ncomms15883, 2017.
Zuend, A., Marcolli, C., Luo, B. P., and Peter, T.: A thermodynamic model of mixed organic-inorganic aerosols to predict activity coefficients, Atmos. Chem. Phys., 8, 4559–4593, https://doi.org/10.5194/acp-8-4559-2008, 2008.
Zuend, A., Marcolli, C., Booth, A. M., Lienhard, D. M., Soonsin, V., Krieger, U. K., Topping, D. O., McFiggans, G., Peter, T., and Seinfeld, J. H.: New and extended parameterization of the thermodynamic model AIOMFAC: calculation of activity coefficients for organic-inorganic mixtures containing carboxyl, hydroxyl, carbonyl, ether, ester, alkenyl, alkyl, and aromatic functional groups, Atmos. Chem. Phys., 11, 9155–9206, https://doi.org/10.5194/acp-11-9155-2011, 2011.